Gas fireplace service
Sweep & inspection
Caps & crowns
Flue relining
Masonry repairLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
See the difference
Before
After
Before
After
Before
AfterHow Much Does Fireplace Services Cost in St. George?
Fireplace services in St. George typically run $150 to $350 for a chimney sweep and inspection, $300 to $900 for common repairs like a cracked crown or damaged damper, and $1,800 to $4,500 for a full liner replacement. A dryer vent cleaning, the other half of home venting safety, usually lands between $100 and $200. Those ranges cover most residential work here, and the written estimate you get before any work starts sets the final price.
What we see across the St. George area shapes these numbers in ways a national price list won’t show you. This is high-desert country, and the swing between a 105-degree July and a freezing January night works on masonry and metal the same way it works on everything else out here. Below we break the pricing down line by line, explain what moves a job up or down, and help you tell the difference between work that needs doing now and work that can wait.
- Typical sweep and inspection: $150-$350
- Common repairs (crown, damper, cap, firebox): $300-$900
- HeatShield ceramic resurfacing: $1,200-$2,500
- Full stainless liner replacement: $1,800-$4,500
- Dryer vent cleaning: $100-$200
Fireplace Services Cost Breakdown (2026)
Here’s what the main categories of fireplace work cost in St. George going into 2026. Ranges assume a standard single-story home with a masonry or factory-built fireplace and reasonable access. The written estimate is always the real number, because a job that looks routine from the driveway can change once we’re on the roof.
| Service | Typical St. George Range | What It Covers |
|---|---|---|
| Chimney sweep and Level 1 inspection | $150-$350 | Creosote removal, flue check, firebox and damper review |
| Level 2 camera inspection | $250-$500 | Video scan of the flue interior, required before a liner job |
| Dryer vent cleaning | $100-$200 | Full lint removal from the duct run, airflow check |
| Crown repair or rebuild | $400-$900 | Sealing hairline cracks up to rebuilding a failed crown |
| Damper repair or replacement | $300-$700 | Throat damper or top-seal damper work |
| Chimney cap installation | $250-$600 | Stainless cap sized to the flue, with spark screen |
| Firebox repointing or repair | $500-$1,500 | Rebuilding deteriorated mortar joints in the firebox |
| HeatShield ceramic resurfacing | $1,200-$2,500 | Restoring a compromised clay liner without full relining |
| Full stainless liner replacement | $1,800-$4,500 | New insulated liner, typically DuraFlex or Olympia Chimney |
| Masonry tuckpointing above roofline | $800-$2,500 | Grinding out and repacking failed exterior mortar joints |
A few things push a St. George job toward the top of a range. A two-story home means more ladder time and more setup. A chimney with a heavy creosote load from burning green wood might need a second pass. And a liner replacement on a chimney with an offset or a damaged clay flue can take longer than a straight shot. On the other side, a clean, well-maintained chimney that’s been swept regularly usually comes in at the low end, because the inspection is quick and there’s nothing to fix.
One note on materials: the liner brands we install – DuraFlex, Olympia Chimney, Gelco, Copperfield, Famco – cost more than the thin hardware-store kits, and they’re what professional chimney contractors specify. A cheaper liner that fails in a few years costs more than doing it right once. When you compare quotes, check what liner is being proposed. That single detail explains most of the gap between a $1,800 bid and a $4,000 bid.
What Affects Fireplace Services Pricing in St. George
- The condition of the chimney when we arrive. A chimney swept every year or two needs less work than one that hasn’t been touched in a decade. Heavy creosote buildup, a crumbling crown, or a flue full of debris from a nesting bird all add labor. The sweep itself is often the cheapest part of a visit.
- Your home’s footprint and roofline. St. George has plenty of single-story ranch homes where the chimney is easy to reach, and plenty of newer two-story builds with steep pitches. Roof access is the single biggest swing factor in labor on any repair. A chimney that needs a ladder and a harness takes longer than one you can reach from a low slope.
- How the fireplace was built. A modern factory-built fireplace with a metal flue behaves differently from a site-built masonry chimney. Factory units often need specific liner components sized to the appliance, and those parts cost what they cost. Masonry chimneys may need HeatShield resurfacing or partial rebuilding.
- Whether the job can be done in one visit. We carry DuraFlex flexible liner systems in inventory, so a liner replacement usually doesn’t wait on a special order. That keeps the schedule tight and the cost predictable. Jobs that need custom masonry, like a crown rebuild, take longer by nature.
- The desert climate’s effect on masonry. St. George swings from triple-digit summer heat to hard winter freezes, and that expansion and contraction cracks mortar joints over time. Chimneys here often show exterior joint failure sooner than chimneys in milder climates. Tuckpointing above the roofline is common work in this market, and it’s priced by the linear foot of joint repaired.
- Whether you need a Level 2 inspection. If you’ve just moved into an older home, changed the appliance, or there’s been a chimney fire, a camera inspection is the right call before anyone quotes a repair. It costs more upfront and saves you from paying for work based on guesswork.
What Do Chimney Sweeps and Inspections Cost in St. George?
A standard chimney sweep with a Level 1 inspection in St. George runs $150 to $350, and most homes fall in the middle of that. The sweep removes creosote and soot from the flue, and the inspection checks the firebox, damper, smoke chamber, and the visible portion of the flue from the roof and the firebox. A clean chimney and a safe chimney aren’t always the same thing – we check for both, because the sweep tells you what’s in the flue and the inspection tells you whether the chimney is sound.
St. George homeowners often burn through the cooler months and then leave the fireplace alone from May to October. That’s fine, but creosote that sat all summer is still there in the fall, and a chimney that hasn’t been looked at since last winter can develop cracks the homeowner never sees. An annual sweep before the burning season is the cheapest insurance in the house.
What Do Chimney Repairs Cost in St. George?
Chimney repairs in St. George generally run $300 to $900 for common fixes like a damaged damper, a cracked crown, or a missing cap, with larger masonry work climbing to $2,500 and up. The range is wide because “repair” covers everything from a $250 cap to a firebox rebuild. Here’s how it usually breaks down.
- Crown repair or rebuild: $400-$900. The crown is the concrete cap at the top that sheds water. Hairline cracks can be sealed; a crown that’s pulling away from the flue needs rebuilding. This matters more here than in wet climates, because a failed crown lets water into masonry that then freezes and spalls.
- Damper repair or replacement: $300-$700. A damper that won’t close lets heated air out of the house all winter and lets cold air in. Top-seal dampers, which close at the top of the flue, are a common upgrade and priced in this range.
- Chimney cap: $250-$600. A stainless cap with a spark screen keeps rain, birds, and debris out. It’s inexpensive relative to the damage an open flue allows.
- Firebox repointing: $500-$1,500. The mortar joints inside the firebox take direct heat and fail over time. Repointing restores them before the firebox brick itself is damaged.
- Tuckpointing above the roofline: $800-$2,500. Exterior mortar joints on St. George chimneys take a beating from sun and freeze-thaw. Grinding out and repacking those joints keeps water out of the chimney structure.
If a repair turns up during your sweep, we have the parts and skills to fix most of it in the same visit. That’s a different experience from a sweep service that hands you a list of deficiencies and drives off. If we find something, we can correct it.
What Does Liner Repair or Replacement Cost in St. George?
Chimney liner work is where the price spread is widest. A full stainless liner replacement in St. George runs $1,800 to $4,500, and HeatShield ceramic resurfacing – which restores a damaged clay liner from the inside – runs $1,200 to $2,500. The right choice depends on what the camera inspection shows, and we’ll tell you honestly which one you need.
A cracked or deteriorated liner is a genuine safety concern. Combustion gases, including carbon monoxide, can escape through gaps in the liner into the home. This isn’t a job for a homeowner with a ladder and a tube of sealant. It’s a trained-professional repair, and the inspection should come before anyone quotes a price. If the flue has a sound clay liner with minor surface damage, HeatShield resurfacing can restore it and extend the chimney’s life without the cost of a full reline. If the liner has gaps, missing sections, or a shifted offset, a new stainless liner is the right answer.
We install liner systems from DuraFlex, Olympia Chimney, Gelco, Copperfield and Famco – the product lines professional chimney contractors specify. A liner is a permanent component of the house, and it’s worth specifying one that will last. When a proposal comes in well below the range above, ask what liner is being used. That question usually settles the difference.
What Does Dryer Vent Cleaning Cost in St. George?
Dryer vent cleaning in St. George typically costs $100 to $200, and it’s the least expensive fire-safety service a homeowner can buy. A clogged dryer vent is the leading appliance-related house fire cause in the country, and it’s entirely preventable. Lint builds up in the duct run, restricts airflow, and creates a fuel source right next to the heat of the dryer.
Dryer vents and chimneys are your home’s two highest fire-risk venting systems. We handle both under one company, so you’re not juggling two contractors. If you’re already having the chimney swept, adding the dryer vent is straightforward. If your dryer takes two cycles to dry a load, or the outside vent flap doesn’t open when the dryer runs, that’s the sign to have it cleaned.
How to Save on Fireplace Services in St. George
The most reliable way to save is to keep the chimney swept and inspected on a regular schedule. A $150-$350 sweep every year or two catches small problems – a hairline crown crack, a damper that’s starting to stick – before they turn into $1,500 masonry repairs. Water damage is the expensive kind, and most of it starts with a detail someone could have sealed.
Other ways to keep costs down:
- Burn seasoned wood. Dry, seasoned firewood burns cleaner and produces far less creosote than green wood. Less creosote means a faster sweep and lower risk of a chimney fire. If you’re buying wood, ask how long it’s been split and dried.
- Get the inspection done before the repair quote. A camera inspection that costs a few hundred dollars can save you from paying for the wrong repair. It’s the difference between guessing and knowing.
- Ask about HeatShield before assuming you need a full reline. If your liner has surface damage but is structurally sound, ceramic resurfacing can restore it for less than a full replacement. Not every chimney qualifies, but it’s worth the question.
- Bundle the dryer vent with the chimney sweep. Having both venting systems serviced on one visit saves you a separate trip and keeps the whole house’s fire-safety picture current.
- Deal with small issues promptly. A cracked crown sealed now costs a fraction of a crown rebuild later. A chimney cap installed before birds nest in the flue prevents a messy, labor-heavy sweep.
We offer free estimates, so there’s no reason to guess at the number. Call (877) 327-1971 and we’ll set up an estimate. We answer 24/7. Fast dispatch from 7am to 7pm.
Why Glacier Chimney Sweep for Fireplace Services in St. George
Most fireplace work comes down to two questions: what does the chimney actually need, and who’s going to do it. Glacier Chimney Sweep handles all three service categories – chimney sweeping and inspection, chimney repair, and dryer vent cleaning – so the same company that finds a problem can fix it. Our technicians have up to 12 years of experience, and we’re licensed and insured.
We use professional-tier product lines – DuraFlex, HeatShield, Gelco, Olympia Chimney, Famco, Copperfield – the same brands chimney engineers specify, not hardware-store substitutes. We carry DuraFlex flexible liner systems in inventory, so liner installation or replacement can often be completed in one visit without waiting on a special order. And we’ll be straight with you about what needs fixing now versus what can wait.
If you’ve just moved into a St. George home with a fireplace you’ve never used, the first step is a sweep and inspection. That gives you a baseline and a clear picture of what you’re working with. From there, repairs are quoted in writing, per job, so the number you see is the number you pay.
FAQs – Fireplace Services Cost
How much does a chimney sweep cost in St. George?
A chimney sweep and Level 1 inspection in St. George typically costs $150 to $350. Most single-story homes with normal creosote buildup come in near the middle of that range. Call (877) 327-1971 for an exact quote – estimates are free.
Is it cheaper to repair or replace a chimney liner?
Repair is usually cheaper when it’s an option. HeatShield ceramic resurfacing runs $1,200 to $2,500, while a full stainless liner replacement runs $1,800 to $4,500. Whether resurfacing is appropriate depends on what the camera inspection finds, and we’ll tell you honestly which one your chimney needs. Call for a free estimate.
How much does a fireplace repair cost in St. George?
Common fireplace and chimney repairs in St. George run $300 to $900 – a damper, a crown, a cap, or repointing. Larger masonry work, like a firebox rebuild or extensive tuckpointing above the roofline, can climb to $2,500 or more. The written estimate sets the final price. Call (877) 327-1971 to schedule one.
How much does dryer vent cleaning cost in St. George?
Dryer vent cleaning in St. George generally costs $100 to $200. It’s worth doing if your dryer takes longer than one cycle to dry a load or the outside vent flap stays closed while the dryer runs. Call us and we can schedule it alongside a chimney sweep.
Can you come today?
Often, yes. We offer same-day service when the schedule allows, with fast dispatch from 7am to 7pm, Sunday through Friday. We answer 24/7. Call (877) 327-1971 and we’ll find the next opening.
Pricing reflects the St. George market as of 2026. Glacier Chimney Sweep offers free estimates – call (877) 327-1971.
Written by the team at Glacier Chimney Sweep.
What Our Customers Say
"Good work. The written inspection report took about a week to arrive after I asked for it, which was slower than I expected."
- Eric Delaney"Swept it, capped it, and installed a proper damper. The downdraft smell in the summer that we'd lived with for years is gone."
- Nathan Pruitt"Crown was cracked and taking water. Repaired it rather than quoting a rebuild, which the previous company had pushed hard for."
- Laura Doyle